Keysight (Agilent HP) E5062A Repair Service
Product model
E5062A ENA Series Network AnalyzerServices
Keep your Agilent E5062A Network Analyzer in service with our repair and calibration. We specialize in unsupported equipment. Free evaluations.
Description
The Agilent E5062A is a member of the ENA Series network analyzers. The E5062A addresses a broad range of measurement needs of electronic components and circuits from low to high frequencies. The E5062A now provides a new standard of frequency-domain device analysis from 5 Hz to 3 GHz.
Repair prices
Any failures or unforeseen issues identified during the calibration phase will be detailed in an estimate submitted for your approval prior to any further action. Repair charges are determined by the actual time and materials required. Please be aware that customers are responsible for all associated shipping costs, to and from our location. This initial estimate is provided free of charge.
E5062A Specifications – click to expand
E5062A Specifications
- ENA-series vector network analyzer
- Windows-based with color display, LAN, USB and GPIB interfaces
E5062A Options – click to expand
E5062A Options
- 150/250, 50 Ohm Transmission/Reflection or S-Parameter Test Set. 175/275, 75 Ohm Transmission/Reflection or S-Parameter Test Set
- 1E5, High-Stability Frequency Reference
- 100, Fault Location and Structural Return Loss
Agilent / HP E5062A Error Codes – click to expand
Agilent E5062A Error Messages
The E5062A messages below are the ones that point to hardware, followed by what a failed performance test means on this model. Errors show on a red bar at the lower left; numbered ones can be read over GPIB.
E5062A notes
- The E5062A runs a power-on self test at every start; a failure is reported as error 241 and broken down by the internal test in the service menu.
- If the rear fan does not run, the A50 power supply is suspect; check the +3.3 V / +5 V monitor LEDs on the A21 PCI DSP card.
E5062A hardware errors
| Error | Message | Meaning |
|---|---|---|
| 220 | Phase lock loop unlocked | A synthesizer PLL lost lock during measurement. The service manual points to the A1 source board. |
| 241 | Power on test failed | The power-on self test found a hardware fault. Run the internal test from the service menu; the first failed test identifies the board (A1 source, A2 receiver board). |
| 240 | Calibration data lost | The system calibration file is missing or damaged at startup. The analyzer needs its adjustment data restored or regenerated. |
| 221 | Port 1 receiver overload | Too much power into port 1. If it appears with nothing connected, the analyzer is faulty. |
| 222 | Port 2 receiver overload | Same as 221 for port 2. |
| 61 | Power unleveled | Requested output power is outside the leveling range after correction. |
| — | Fatal Error: Failed to Initialize DSP / DSP Driver | The A21 PCI DSP card or A20 digital motherboard did not start. Also shown after a failed firmware update. |
| — | Fatal Error: Failed to Update DSP Code | Writing DSP firmware to flash on the A21 PCI DSP card failed; reinstall firmware, then suspect A21 PCI DSP card or A20. |
E5062A calibration, file and setup errors
| Error | Message |
|---|---|
| 20 | Additional standard needed |
| 22 | Calibration method not selected |
| 30 | Valid ECal module not found |
| 31 | Failed to configure ECal module |
| 41 | Peak not found |
| 53 | Log sweep requires 2 octave minimum span |
| 100 | Failed to read file |
| 101 | Failed to write file |
| 105 | Recall failed |
| 106 | Save failed |
| 120 | Printer error |
| 200 | Option not installed |
SCPI error ranges
| Range | Class |
|---|---|
| −100 to −199 | Command errors |
| −200 to −299 | Execution errors |
| −300 to −399 | Device-specific errors |
| −400 to −499 | Query errors |
Hardware error on your E5062A? Analyzer Repair Inc. repairs and calibrates the Agilent E5062A in-house in Cocoa, Florida. Free estimate once the unit is in our lab. Contact us for service.
Based on the Agilent E5061A/E5062A ENA Service Manual (E5061-90140).
Agilent / HP E5062A Replaceable Parts – click to expand
Agilent E5062A Replaceable Assemblies and Part Numbers
Assembly-level part numbers for the E5062A. Check your options before ordering option-only parts.
| Reference | Assembly | Agilent part number | Notes |
|---|---|---|---|
| A1 | Source board | E5062-62111 | Exchange E5062-69111 |
| A2 | Receiver, 50 Ω | E5062-62011 | Options 150, 250; exchange E5062-69011 |
| A2 | Receiver, 75 Ω | E5062-62012 | Options 175, 275; exchange E5062-69012 |
| A20 | Digital motherboard | E5062-62003 | |
| A21 | PCI DSP card | E5062-66521 | |
| A24 | PCI GPIB card | E5062-65000 | |
| A22 | Front panel keyboard | E5062-66522 | |
| A27 | Hard disk drive | E5062-83102 | |
| A28 | Floppy disk drive | 0950-5083 | |
| A50 | Power supply | 0950-4773 | |
| A52 | Inverter | 0950-4091 | |
| — | Analog motherboard | E5062-66510 | |
| — | LCD assembly | E5070-60101 | Touch-panel LCD E5070-60102 with Option 016 |
Part obsolete? Many E5062A assemblies are no longer sold new. Analyzer Repair Inc. repairs E5062A boards and RF modules at the component level in Cocoa, Florida. Free estimate once the unit is in our lab. Contact us for service.
From the Agilent E5061A/E5062A ENA Service Manual (E5061-90140).
Located in: Network Analyzers